|
|
DVC41 High Side Output Expansion Module
|
||||||||
|
|
The DVC41 Expansion Module is a 12 Sourcing output module for the DVC10 controller. The 12 Sourcing outputs can be configured to drive substantial loads up to 3 amps. The DVC41 can also be configured to drive LED outputs. The outputs are short protected and have built in open detection. The DVC41 communicates to the DVC10 controller module through the CAN Bus (high-speed serial communication bus) and utilizes the RS-232 port for setting the MAC ID (node) number and for device monitoring. The controller is packaged in a small rugged enclosure and encapsulated to withstand extremely harsh environments.
Click to Enlarge Two connectors P8 and P9 are provided for electrical connections. P8 (30 pin) is the main input and output connector which protrudes out the side of the enclosure. P9 is a standard DeviceNet Compatible (CAN Bus 2.0B) 5 pin connector. The status of each output is displayed by a green LED located on the top of the module. If the output is activated, the corresponding LED will light. If the output is being used and has an open circuit, then the corresponding LED will blink slowly (once a second). If the output is shorted, the corresponding LED will blink fast (four times a second). A Module Status (Red / Green LED) and a Network Status (Red / Green LED) LED are also located on the top of the module (see INDICATORS section below for further details).
Rugged Construction: ¨ Rugged encapsulated enclosure withstands harsh environments commonly found in mobile applications. ¨ All connectors are sealed and the module is encapsulated to withstand extreme conditions in the harsh mobile operating environment. ¨ Operating Temperature: -40 Celsius to 85 Celsius ¨ Storage Temperature: -40 Celsius to 85 Celsius Setup and Installation ¨ User programmable. ¨ Physical Size - 6.2L” x 4.75W” x 1.65H” encapsulated module. ¨ Each module has two mounting holes 4.0” a part. Mounting hole I.D. is 0.325”. ¨ An RS-232 port is used for setting MAC ID (node) number. Power Supply: ¨ Rugged power supply operates over the full range 8.5Vdc to 32Vdc. ¨ Reverse polarity protection and transient protection up to 1.5K watts peak pulse power dissipation.
¨ All outputs are sourcing. ¨ Vehicle +Power will be applied to the output when the output is activated. ¨ Maximum Output Load = 3.0 amps. ¨ Each output has a corresponding indicator to tell whether the output is on, off, shorted or open. ¨ Programmable outputs: Each output can be named (16 characters). Normal load mode – Used for driving all loads up to 3amps. LED output mode – Used for driving LEDs or low current indicators. Communications: ¨ Can Bus 2.0B: Communication port to the DVC10 Master Module. ¨ RS-232 serial port: Setting MAC ID and Baud Rate & Monitoring the functions of the DVC41. Indicators: ¨ Output Status (Qty 12) (Green) Off – output is off. On – output is being activated. Open Circuit – blinks once per second. Short Circuit – blinks 4 times per second. ¨ Module Status (MS) (Qty 1) (Red / Green) – Off – There is no power applied to the Module. On green – The module is operating in a normal condition. Flashing green – Device in standby state. May need commissioning. Flashing red – Recoverable Fault. On red – Module has an unrecoverable fault. Flashing Red/Green – Device is in self-test. ¨ Network Status (NS) (Qty 1) (Red/Green) – Off - Device is not on-line. Flashing green – Device is on-line but has not established connection to other nodes. On green – Device is on-line and has established connection to other nodes. Flashing red – One or more connections are in a timed-out state. On red – The device has detected an error rendering it incapable of communicating on the network. Connectors: ¨ Metri-Pack 150 series (or compatible) sealed electronic header designed for severe under-hood environments. 30-pin Header (P8) 5-pin CAN Bus (DeviceNet compliant) connector (P9). Protection rating – Nema 1,3,4,6P, and IEC IP 68. Mating Connector Kits: or Mating Connector Assemblies with flying leads for Start-up applications ¨ Mates to the 30-pin Metri-Pak Connector (P8): Connector, 30-pin Female (P8) Delphi Packard P/N – 12048455 Terminals, Female Delphi Packard P/N – 12103881 Plugs Delphi Packard P/N – 12034413-B Terminal Crimp Tool Delphi Packard P/N – 12039500 Extraction Tool Delphi Packard P/N – 12094429 ¨ DVC Series 30-pin Connector Kit, HCT P/N: 999-10085 Includes the following: Connector, 30-pin (P8) Delphi Packard 30 - Terminals, Delphi Packard 20 – Plugs, Delphi Packard ¨ Mating for CAN Bus connector (P9) 5-pin Female Mini-style DeviceNet compliant connector. ¨ Mating to the RS-232 Port DVC Slave Serial Port Adapter, HCT P/N: 999-10082 DVC RS-232 Cable Assembly, HCT P/N: 999-10075
© Copyright 2009 High Country Tek, Inc. All Rights Reserved.
|
Outputs – Qty (12):