|
208 Gold Flat Court Nevada City, CA 95959 Ph: (530) 265-3236 Fx: (530) 265-3275
Contact HCT for more information or a worldwide distributor near you.
|
High Country Tek, Inc.
Electronic Control Solutions for the Global Fluid Power Industry
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
The DVC module family is user programmable with combinations of modules able to support a wide range of hydraulic control applications. The DVC7 and DVC10 are the master controllers and their flexible hardware and software allow them to run many hydraulic control applications as a single module. The DVC7 & DVC10 and all DVC expansion modules are packaged in small rugged enclosures. All connectors are sealed and each module is encapsulated to withstand extreme conditions in harsh operating environments. The hardened enclosures allow you to locate the DVC modules near the sensors, valves, etc. they will control. This can greatly minimize the amount of cabling in your system and significantly lower your costs... read more
The electronic controllers offered below gives the user the ability to tailor the application to their customers requirements and without specialized training while offering the industries most robust packaging. These units are designated as "Application Specific" which means they offer a cost effective, flexible but focused dedicated solutions to a common issue, set-up, operation and getting your application from the drawing board to your customer in record time.
Hydraulic Fan System Controllers such as the HFS controls a hydraulically driven fan system. The HFS controller accepts three thermistor and two digital inputs and provides a PWM output to control the proportional valve of the fan drive. The HFS-2 adds the reverse or purge feature to the HFS. And the new HFS-J has the added feature of J1939 CANbus communication. The HFS-J-Emotor has been designed to interface with an electric motor cooling system.
The latest in the fan control line it the new Plug Top Driver (HFS-3) series with the DIN 43650 footprint and direct connect to low frequency PWM engine ECU fan speed signal. Or the new HFS-4 with direct connect to low frequency PWM engine ECU fan speed signal.
Hydraulic Generator Controllers - The HGC-2 is designed to control a generator driven by a hydraulic motor where speed is controlled by a proportional solenoid valve, either directly at the motor or as part of the pump compensator. The HGC-2 is a closed loop controller that monitors the AC line voltage from the generator output for outer loop closure and provides the necessary current to a valve coil in order to maintain the desired generator frequency.
Power-Line (PLD) - The universal single or dual coil PWM driver to stock for your open loop amplifier, electronic HP limiter and closed loop speed control applications. √ Standard open loop proportional driver √ RPM Regulator Anti-Stall/ HP Limiting Controller
√ Closed Loop Control The HAU series valve driver provides precise control of a single coil proportional valve and enables the user to add ramping and/or dither to minimize stiction and hysteresis of the valve. The HAD series valve driver is the same as the HAU, but drives a dual coil proportional valve. The LCU, a single coil proportional valve driver tailored for use on low current EDC valves such as Sauer-Danfoss™ 90 series.
The new Plug Top Drivers (PTD) are designed to control single valve coils, and come in 12 or 24V versions that can interface with 4-20mA or 0-10V command signals and connection to any valve with a DIN 43650 interface.
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Electro-hydraulic controls, single solenoid controllers, dual solenoid drivers for proportional and directional valves, potentiometer and PWM controllers, digital controls, RPM comparators, solenoid drivers, dc-dc converters, hydraulic generator controls, fan drive controls, networked control systems, valve drivers for proportional cartridge valves, controllers with feedback, I/O with CAN communications, joystick interfaces, electronic controllers, LCD and Graphical Display's, PID control, spool position feedback, pwm converters, networked controls with CAN bus, SAE J1939, DeviceNet, transmission controllers, robotics, motion control, closed loop controls, temperature set point controller, engine controls, engine control module interfaces, resolver signal conditioner, operator interface, material handling equipment control systems, actuator controls and other electro-hydraulics for off-road construction equipment, off-highway vehicles, trucks, buses, lift equipment, forklifts, mobile equipment and agricultural machines. Motion control modules are High Country Tek’s specialty using our patented technology and Intella Software Suite with program loaded monitor.
© Copyright 2009 High Country Tek, Inc. All Rights Reserved.
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
